Food and Drug Administration (FDA) Disclosure:

The statements in this forum have not been evaluated by the Food and Drug Administration and are generated by non-professional writers. Any products described are not intended to diagnose, treat, cure, or prevent any disease.

Website Disclosure:

This forum contains general information about diet, health and nutrition. The information is not advice and is not a substitute for advice from a healthcare professional.

Would this work ?

Discussion in 'Apprentice Marijuana Consumption' started by Johnywilks, Feb 8, 2011.

  1. #1 Johnywilks, Feb 8, 2011
    Putting a whole in the top of a gatorade bottle, putting in socket wrench bit ( for cone ) . Filling bottle up halfway with water. Lighting the weed , take the lid off and inhale the smoke.


    Would that work?????:confused:
     
  2. #2 V4p35 McG33, Feb 8, 2011
    No you need some kind of suction either cutting the bottle in half and sticking it in a pitcher or sink, or you need to make a hole by the top of the lid where you can inhale. It also would be a good idea to make some kind of screen for the socket/bowl.
     
  3. #3 Cubs Guy17, Feb 8, 2011
    We will disregard the issues of no suction power, very loose joints, and no way to keep the bud in the bowl and move to a simpler one. Do NOT fill up the bottle halfway with water. Just a little bit so the downstem (assuming you put one in this elaborate blueprint you have drawn up) is submerged like a half inch to an inch. If you want to work on the achitecture/suction power maybe we can work something out. Not much can be done for those loose joints other than gum and super glue and that only works half ass at best.
     
  4. #4 Johnywilks, Feb 8, 2011
    no down stem. But it the bit holds in place perfectyly air tight. What will happen ???

    Do i have to cut the bottom off and put it in a bucket
     
  5. #5 Cubs Guy17, Feb 8, 2011

    if the bit holds and there is no downstem I assume this bong uses a carb? I would suggest cutting off the top of the bottle and flipping it upside down to create a stronger pull when you hit it, giving you a bigger hit. Just hot glue it and you should be good. What kind of gatorade bottle are you using?
     
  6. #6 Sunn, Feb 8, 2011
    put a hole in the bottom of the bottle and hold it covered with your finger. then start torching the weed and let go of the hole (over a sink or something, obviously). then just wait for the bottle to fill up. once its done you take off the top and enjoy. that's a waterfall bong.
     
  7. #7 Cubs Guy17, Feb 8, 2011

    AHHHHH Sunn you bring back some good memories. I haven't made a portable waterfall bong since middle school. + rep
     
  8. #8 iCremateCanabis, Feb 8, 2011
    Idk what the fuck u just said OP, but test it out yourself without ganja and see
     
  9. #9 Johnywilks, Feb 8, 2011
    How do i test it without the weed?
     
  10. #10 AZBLAZER420, Feb 8, 2011
    Sounds like you want to make a waterfall bong. The waterfall is defiantly one of my favorite pieces to toke from. So I will tell you how to make it. Find a big bottle preferably a 2 liter or a smart water. Put a socket through the lid. then make a whole on the side near the bottom of the bottle. Load the bowl. Fill it up almost all the way with water. You got to hold the hole when you are filling it up. Then put the cap on. Go outside or in a sink. Light the bowl and at the same time release your finger and the water going out that hole will fill up with milky smoke. Then screw the top off and suck all the smoke up. Its ok if you cant clear it. Enjoy!:D
     
  11. #11 Johnywilks, Feb 8, 2011
    I only have a tiny 4mm socket bit, is that to small??

    i could get a bigger one but the hole at the bottom looks like to big ( it would just fall thorugh)
     
  12. #12 BalkanCommie, Feb 8, 2011
    this is what i do

    1. put a hole in the Gatorade cap
    2. put the wrench socket in the hole of cap
    3. take the Gatorade bottle and put a hole in the bottom side
    4. get out a plastic trash can fill it with water(about 2 inches from top of bottle)
    5. take out the bottle fill it with water from your trashcan now once its filled take the bottle out and put your finger on the hole :eek:QUICK!
    6. put the loaded(with weed) Gatorade cap and tighten it on the bottle
    7. now get the lighter and let the hole go as your lighting the weed, and as soon as its lit put your lighter away and watch the water fall out and the milk come in :smoke: yeeaahh
     

Share This Page