How To Attach L.e.d Light To My Bong

Discussion in 'Smoking Accessories Q&A' started by rastafarmer1, Jun 17, 2013.

  1. #1 rastafarmer1, Jun 17, 2013
    how do i attach an l.e.d light to my bong
     

     
  2. #2 DMaldonado93, Jun 17, 2013
    u got to be a little more specific like where? just remember all it takes is a component, power source, and a switch
     
  3. #3 rastafarmer1, Jun 17, 2013
    i am not sure u got advice/ anyone got exprience
     
  4. #4 Dr. Sheldon Cooper, Jun 17, 2013
    We don't know what you want though?
     
    Or what bong you have.
     
    Basically, you'll need to strap the lights somewhere, find a way to attach a switch to the bong, and a battery. Wire them all together, and let there be light.
     
  5. #5 Kryptix, Jun 17, 2013
    Easy. Just use an adhesive from Home Depot
    [​IMG]
     
  6. #6 rastafarmer1, Jun 17, 2013
    where do i get LEDs that flash cool coulers online
     
  7. #7 SiriusWolff, Jun 17, 2013
    Last edited by a moderator: Jun 17, 2013
    Man you really need to learn how to use google. We can't spoon feed you info that is readily available at the click of a mouse. Not to be a dick i'm just saying some people don't take kindly to posts like this.
     
    What we need to know is, what kind of bong, what kind/power of lights you want, where you want to put them, how you plan to make a switch, what kind do you want. etc
     
  8. #8 theicemanmypass, Nov 4, 2014
  9. #9 theicemanmypass, Nov 4, 2014
  10. #10 theicemanmypass, Nov 4, 2014
    If your bong is glass or plastic the best way to aluminate it is to shine light from the top or the bottom as it will cover the most service area then just from the side


    Sent from my iPhone using Grasscity Forum
     
  11. #11 ispeakforthetrees, Nov 8, 2014
    Lmao!
    Maybe the original question should have been "how did you attach an LED to your bong?" ?


    Sent from my iPhone using Grasscity Forum
     
  12. #12 theicemanmypass, Nov 8, 2014
    I have not attached one to my bong yet because I don't know if I want to go with an LED light up base plate or an LED light up

    strips ImageUploadedByGrasscity Forum1415438781.538537.jpg

    ImageUploadedByGrasscity Forum1415438813.709856.jpg


    Sent from my iPhone using Grasscity Forum
     
  13. #13 SkunkWoodz, Nov 8, 2014
    My friend wired up a battery pack and a switch where you would normally hold the bong and a strip or two running through the inside of it.  It was pretty fuckin ghetto but first light up bong I'd seen.
     
  14. #14 Sssnakepit420, Nov 10, 2014
    If you want to see quality lights in bongs. Check out N3rd Glass. Guy absolutely kills it.


    Sent from my iPhone using Grasscity Forum
     
  15. #15 123burnthattree, Nov 10, 2014
    Last edited by a moderator: Nov 10, 2014
    Dont they have glow in the dark beads you can put in the bong? Also i wpuld recommend using the LED base you showed in the first picture. Get a little battery back and run the wires. Show us your bong


    Edit: You may also be able to use the strips on the very bottom of a bong not quite the base. But wrap it around the bottom of the bulb so the lights point up somewhat
     

Share This Page