Dismiss Notice
Food and Drug Administration (FDA) Disclosure:

The statements in this forum have not been evaluated by the Food and Drug Administration and are generated by non-professional writers. Any products described are not intended to diagnose, treat, cure, or prevent any disease.

Website Disclosure:

This forum contains general information about diet, health and nutrition. The information is not advice and is not a substitute for advice from a healthcare professional.

How Full Do you fill up the bubbler?

Discussion in 'Beginner Cannabis Consumption & Tips' started by blakegoehring24, Aug 23, 2008.

  1. #1 blakegoehring24, Aug 23, 2008
    just got a double bubbler and i need to know how much water i should put in it?
     
    • Winner Winner x 1
  2. #2 Caboose, Aug 23, 2008
    normally i just add enough to cover the stem. (the pipe that goes down from the bowl)

    i dont recommend filling it through the bowl cuz youll get ur bud wet
     
  3. #3 Albie, Aug 23, 2008
    you can also put water in your mouth and (i cant think of a better word) spit the water into the carb utill you have covered the stem. This also allows you to load the bowl dry, and then put in the water after.

    edit: im assuming you have a carb :)
     
  4. #4 nuentoter, Aug 23, 2008
    put enough so your downspout is under water but not too much so that if you take a decent rip you get a mouth full of water. also too much water may lead to water bubbling up into your bowl.
     
  5. #5 mr.tokes, Aug 23, 2008
    put the water in through the bowl (where you put the weed), wipe off the mostuire
     
  6. #6 dr dre, Aug 23, 2008
    in the mouthpiece bro. do you really want a bubbler bowl with wet resin in it?
     
  7. #7 ckycampmember, Aug 23, 2008
    my roommate has a nice bubbler and we just put it in from the bowl.
    then wipe it dry.

    since you just got a bubbler, i would recommend putting it in the freezer for like 5 minutes.
    and putting in water from a water bottle in the fridge.

    its awesome.
     
  8. #8 tastyblunt, Aug 23, 2008

    only thing i have to add to that is please dont take it out of the freezer and put warm water in it. for obvious reasons the glass will warp or worse crack.

    post up some pics of it man !! i wanna see and I can give you good suggestions on how far to fill it up and such !:smoke:
     
  9. #9 blakegoehring24, Aug 24, 2008
    tyvm for the help guys! yegonna put some pics of it up in a day or so in a new thread its pretty cool. Also how the fuck am i supposed to clean it???
     
  10. #10 Vapula, Aug 24, 2008
    I put in just enough water to hear it bubble when I hit it. If it sounds fine, it has enough water. To clean it fill it with alcohol and shake it. You can run hot water through it to rinse it out.
     
  11. #11 shifty, Aug 25, 2008
    use a sport water bottle where u can spray the water
     
  12. #12 blakegoehring24, Aug 25, 2008
  13. #13 TyDurden, Aug 25, 2008
    dude, it looks awesome, Im getting one soon too. This is a very noob question, but when you put the water into it, where does it go? Like, does it go into the left part or the right part. This question makes me sound fucking stupid lol.
     
  14. #14 blakegoehring24, Aug 25, 2008


    by the left or right part you mean the chambers??? the water goes in both
     
  15. #15 TyDurden, Aug 25, 2008
    yea, meant the chambers, so how full are you suppose to fill them?
     
  16. #16 blakegoehring24, Aug 25, 2008
    i appreciated the help of everyone on this thread :) ive only smoked out of it yesterday but i filled about halfway, i just checked it by ma kin it bubble. It hits real smooth
     
  17. #17 CrazyKush, Aug 25, 2008
    just put your sink on a very low setting (so not much water is coming out at once, skinny flow of water idk how to put it lol) and run that through the carb so everything that should be dry is dry.
     
  18. #18 octoganj, Aug 25, 2008

    exactly what I was about to say!
    haha yeah thats the way to go, works like a charm
     

Share This Page