Hey guys, got a vapir rise yesterday and got kinda high off it yesterday, the vapor I got was really not dense at all at times I was questioning weather I was vaping at all, I was usually between 365 and 380 degrees and fan setting 2 or 3, the bag was still filling up fairly quick and the vapor wasn't very dense compared to an e cig or liquid vaporiser which was somewhat doss appointing, anyway I've looked everywhere and can't find optimal settings and playing around wasn't going to well for me, is there a certain amount of herb that works best in the chamber too? Anyone who's used one of these please let me know your settings for the bag and whip systems
yeah I have the 2.0 I hardly use the bags cause I find the vapour to harsh even when running it thru a bong......I dont use the fan jusst pull from the whip 370 for the first few minutes then 280 to finish it up. As far as how much I use enough to cover the bottom pprobably about an 1/8 full just enough for the plunger to touch it.
I've been using my vapirrise for 1 year and I'm super happy with it ... you can not expect the same dense vapor as an e-cig, it will also vary from one weed two one another. I never use balloon mode, always direct Vape as this gives the thickest Vape. remember to always grind your herb very fine and the drier the better. I start at about 380 Ffor 3-5 minutes, then 387 F for 3 min. and ends with full power until no more vapor . (Fan 2. ) Long deep inhalation? I use about 0.3 g per vape session . Gives me about 10 -12 min session. Sent from my iPad using Grasscity Forum
hey Niel, do you have a problem with the plunger rising up as you pull........I find that around 5 minutes or so the plunger will rise up, youll know cause the draw is easier. I found that if it gets too clogged up the plunger will ride.I take a lighter or even sumtimes i use the flame from the gas stove just put the screen part in the flame and it burns out the resin ....but then if you look inside the plunger there will be a bunch stuck up there thats what you wanna scoop out....after its clean the plunger will stay put.
Hi Fredbear Yes the plunger rises up the first few times, when I have just cleaned my vapirrise. I do not see it as a problem, as I always pack my cannabis a bit with my finger before I vape. I clean it a couple of times a week with pure ethanol and rinse with water ( a clean vapirrise also gives a more dense vapor) Sent from my iPad using Grasscity Forum
otherwise I just screw top of while vapeing and push it down again. Sent from my iPad using Grasscity Forum
and as an added bonus I save the honey-colored devils juice left over in the tube . I press it out when the tube is hot. stores it on a spoon. when it's cold, I eat it .. a portion the size of grain will after a few hours leave you smiling stupid.... Sent from my iPad using Grasscity Forum
Over time, the oil or whatever it is, automatically collects in the tube. just do not clean it ..... it depends on how much you vape . I think that this is after vapeing about 30 g of skunk. Sent from my iPad using Grasscity Forum
when the tubes are hot right after a vape session, I use my thumb to press out the oil as shown in the picture. Sent from my iPad using Grasscity Forum
To OP please rememmber vaping only extracts things that you can boil off the plant ( unless you burn it which would be counter productive) so the smoke will be lighter but its light because its cleaner carring only thc and a ton of cbds and leaving cathogens behind which is what makes weeed smoke so thick . So your getting high , its just a head high thats different then smoking , you vape works just fine . Just find out tips and tricks to get the vapor you want . I have a extreme q that i elbow pack to get nice size bowls - in combination with a bong and a 430 burn temp im able to get super baked off small amounts and still get reasonable clouds . https://owensmithe.files.wordpress.com/2014/06/volcano-vapourizer-temperature-chart_-4-22_thumb.jpg So at 430 for the temp you can effectivly vape everything it has to offer but please - if you vape this high be careful not to combust . Aa for the tube extraction - just run a rod or something with about the same hole diameter as the tube through it .