help me out, look at my plans

[lega_c]

This is my plan for a poor man's passive hydro system. I will post instructions. If you still don't get it post your questions. All measurements and system settings(fertilizers, mediums, and timing issues) will have to be sorted out by you. Thank you for looking this over. Any input, criticism or praise is welcome.

(1)
Cut four small holes in the bottom of each cup

Cut two lengths of 1/4" thick nylon cord 9 inches long and place them crosswise in the
bottom of the cups in a criss cross pattern. Make sure the rope hangs an equal length
out of each hole

Cut 2"x2"x1.5" rockwool blocks down so that they fit the bottom half of each cup

Fill the rest of the cup with this soil mix.
1 bag cow manure
1 bag potting soil (no chemicals)
1/2 bag sand
2 cups bone meal
2 cups blood meal
1/2 gallon chicken manure
1/2 cup bat guano
1 cup lime
1 cup worm castings
1/2 cup kelp juice

(all these things can be found at a Home Depot or Wal-Mart)

Plant your germinated seeds or treated clones right into the soil, wet and forget.


__________________________________________________ __________________________________________

(2)

Take the lid of the tuperware container and cut the holes according to the cup/pot size
you plan on using. You want the cup to sit about half way into the tuperware container.
Also, make sure the sides of the cup are as tight to side of the hole in the lid as
possible.

__________________________________________________ ___________________________________________

(3)

Take the actual tuperware container and drill a 1/4" hole in the top of one short side,
3/4's the way up on one long side, and one on the bottom on the opposite end as the first
hole.

Attach drip valve to the hole on the bottom of the tub. To do this use a clear silicon
caulk.

Attach overflow hose to the hole in the middle of the side of the tub(2/3's the way up
the side of the tub). Also use silicon caulk for this.

Fill the tub with grow rocks. You want to fill the tub up to the top of the overflow
hose.

Be sure to raise the end opposite the drip valve 1" for every 30" length of the tub.
__________________________________________________ ________________________________________

(4)

Attach the drip tube to the valve.

Drill two holes into the short side of the top of the cooler. These holes should
be drilled opposite the drain hole on the bottom of the cooler.

Using silicon caulk seal the ends of the drainage and overflow hoses into the two
holes you just drilled into the top of the cooler.

Place the aerator and aquarium heater into the cooler. Test your system for actual
settings for good water quality.(72 degrees f. and plenty oxygen)

__________________________________________________ __________________________________________

(5)

The water filter and pump are a little difficult so try to stay with me here.
Filter Supplies:
(1) 7" piece of 2-2.5" diameter p.v.c. tubing
(1) 6" piece of 1-1.5" diameter p.v.c. tubing
(2) caps that fit your larger p.v.c. pipe
(1) piece of white industrial foam 1/4-1/2" thick
7" wide x 9" long

Tools needed:
Power drill
1/4" drill bit
1/16" drill bit
1/32" drill bit
hacksaw, jigsaw


Directions:

1) Use the 1/16" bit and the power drill to drill eight sets of four holes by drilling
straight through the 2" p.v.c. in rows of four, four times.

2) Use the 1/32" drill bit to drill four sets of four holes through the 1" p.v.c.

3) Size and cut the white industrial foam to the right size to wrap all the way around
small p.v.c. pipe. Wrap it around the pipe and be sure to plug the hole in the
end with a small chunk of foam, however be sure to leave the other end open. Fit this
whole unit into the large peice of p.v.c..

4) Cap the end of the large p.v.c. and affix it with some silicon caulk.

5) Drill a 1/4" hole in the other cap of the large p.v.c.. This is where it could get
tricky. You are probably going to have to splice the water line coming from the
cooler.(or you could just plop the filter right down into the cooler from the side)
Cut the intake end of the water pump off the line giving about 17" of hose left
on the intake end.

6) Shove the intake end of the water pump into the middle peice of p.v.c. Lead the hose throught the hole in the second cap and affix this cap to the large
p.v.c. pipe so that the hose is hanging out one end.

7) Place the filter unit into the bottom of the cooler and lead the tubing throught the
spigot hole on the end at the bottom. Be sure to seal this hole extremely well as it
could result in a very wet grow space.

__________________________________________________ ___________________________________________


If you have any questions post them. Any improvements, post em. Anything to say, post
it

[the rainman!]

shit i dont grow hydro but that was out stand unoit! i like the way you invent what you want and create your own buckets i mush rather go my own path and find my own way ! it give far better resaults ,i am impressed with your willness to work with what you can to make what you want and it shows in your plants as well ,and my hats off for you showing it to others so those that are not as creative can learn as well! i thank you for shareing your ideas with us all here and i would hope see your ideas some day in a grow book ,good luck tazz11

[Big Poppa Puff]

HIGH ALL! Dang Unoit, your system looks real familiar. hmmmmmm?

K.I.S.S. Keep it simple, stupid.

[the rainman!]

two stage hydro pots if he got them from any where it dose 'nt batter much as long as they work dose it did he get the idea from you bpp or from some where else? i just like the design and i dont even grow hydro !but if i did i would use this kind of bucket ,they look great !