Home Made DWC in Stealth Closet

Rumpleforeskin · #1 (**permalink**) 07-09-2006, 11:10 AM

I have posted pictures of my closet on other forums, but a few of my bro's post/boast over here. So I will post a few of my small grow to get advice and share ideas with folks here as well.

This is my clone room and mother plant. I use four 20w florescent bulbs. I turn half off when not cloning.

1st day in main room. Everything is in place for new grow.

Turn on the light!

Looking for leaks. I use no glue, sealer, or metal parts.

400w Grow tube. It does not draw air from the room. The room is a closed system. The plants have a max height of 5'6". I have not had to raise the light to max height yet. I like to keep the plants at about 4'6".

The screen is to keep the plant stable and help train uniform growth.

I use two air pumps that feed three buckets. Each bucket has two airstones.

TDS and PH sensors screw into the side of bucket.

Co2 control with tank.

Top half of my controls. Co2 valves and thermostat.

One intake for the cooling of the light and the other in case the grow gets above 85*

Dampers on the grow intake and exhust to maintain high Co2 levels in the room.

A 6" blower on a thermostat to cool the room and a 4" blower that cools the light.

The light stays cool with a 4" blower that stays on. The air is piped into the light from the outside.

The noise from the air rushing into the closet was so loud, I had to build a muffler on the intake as well. It's kinda hard to get photos of how I did it, so I will have to draw a picture.

Have not got around to painting the outside yet.

8 days later, still in veg cycle.

15 days later I am in day 10 of flowering.

Its day 16 of flowering and we are at alittle over 5' tall.

This is the 5th grow with this set-up. I had four plants last time. I'm only doing three this time. I did my harvest in two cycles, one at 45 days and another at 60 days. Here is a picture of the last two plants I harvested.

I put it all in glass jars when done.

I hope this grow comes out as well.
Peace, R

cantgetenough · #2 (**permalink**) 07-09-2006, 03:58 PM

Dame fine set up Rumpleforeskin

, gives me some great ideas for my current build.Your 400w cool tube, how close can your plants get before getting damaged?

Rumpleforeskin · #3 (**permalink**) 07-09-2006, 08:59 PM

It has a dedicated 4" blower that runs the whole time the light is on. It never has a chance to heat up. Touching the tube would be fine, like I am doing in this picture. The glass stays cool. The light radiates warm rays buy not enough to burn or damage plants. I have the light right on the plants today.

cantgetenough · #4 (**permalink**) 07-09-2006, 10:13 PM

thanks for the demo.This may be a stupid question but do you think that 2x 4" computer fans will do the job in getting air in and out enough to keep it cool

br3ad_ · #5 (**permalink**) 07-10-2006, 12:27 AM

Holy fuck man.

Rumpleforeskin · #6 (**permalink**) 07-10-2006, 04:18 AM

Quote:

do you think that 2x 4" computer fans will do the job in getting air in and out enough to keep it cool

It is possible. It depends on your set-up and location. If your grow draws air from inside your 70 degree home and you grow with low watt bulbs, it can be done.

I re-did my vents and blower set-up six times. I always underestimate how hot it gets in the summer here. I can't draw air from inside my home. If I don't cool my 400w bulb the room will get over a 120 degrees on a cool day.

My advice is "over-kill the hell out of your ventilation system". You can always add a dimmer switch

Peace, R.

PurpleStuffed · #7 (**permalink**) 11-28-2006, 10:09 PM

Awesome Setup very nice.

adb3 · #8 (**permalink**) 11-29-2006, 06:48 AM

Quote:

Originally Posted by br3ad_

Holy fuck man.

yeah, what he said..

Honestly, that is a very impressive, kinda puts to shame what I did in my closet.

CFLdorm · #9 (**permalink**) 12-02-2006, 03:06 AM

holy shit.

how much did that setup cost you?

naughtyneighbor · #10 (**permalink**) 12-02-2006, 04:05 AM

Damn i can tell this is a pro grow lol

canoguy · #11 (**permalink**) 12-08-2006, 05:34 PM

good stuff best ive seen

Rumpleforeskin · #12 (**permalink**) 12-10-2006, 11:10 PM

Thanks for the kind words. I rebuilt this closet about 5 times. I love making stuff myself. I shop around for my junk to try and save money when I have to. I'm in my 40's and have a pretty good job, so I can afford to spend on my hobby. That does not mean I toss money out on every cool gadget. I built most my CO2 system (not the meter). I am in the process of moving the CO2 tanks from inside the grow to the attic. I have to run steel pipe the whole way.

The guys at the welding shop that I buy CO2 from asked "what are you using CO2 for?". I replied "SCUBA-diving, bucause CO2 is cheeper then compressed air". *Thats not the funny part*.............The funny part is they all agreed.
True story. R

ElDust · #13 (**permalink**) 12-11-2006, 03:53 AM

Ah, my dream setup!

Rumpleforeskin · #14 (**permalink**) 12-11-2006, 08:55 AM

After I have this closet working perfect, I plan on following this hobby in the direction of what "Mister Postman" is doing. I like what he has done for indoor growing enthusiast such as myself. If you don't know what I'm talking about, then you have to see what your missing http://forum.grasscity.com/grow-jour...oset-grow.html .

Peace, R.

MrBojangles · #15 (**permalink**) 01-03-2007, 03:36 AM

Peace

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Check out my newest Home Made :)	DiAmOnD RaStA	Recreational Marijuana Use	20	08-09-2005 03:22 AM
home made bong, steem roller, and bodybag pics	coltonwinieckie	Recreational Marijuana Use	8	07-31-2005 05:38 AM
home made pyrex pieces	wafflemanwillis	Recreational Marijuana Use	0	06-09-2005 06:56 AM
home made vap??	weed_josh	Recreational Marijuana Use	1	05-27-2005 09:56 AM
Home made bong or bowl?	IluvRootBeer	Seasoned Tokers	5	10-07-2002 01:08 AM

Site links

FAQ

Important

Extra

#1 (permalink) 07-09-2006, 11:10 AM
Rumpleforeskin Legal Medical Grower Join Date: Jul 2006 Location: SoCal Posts: 3,282	Home Made DWC in Stealth Closet I have posted pictures of my closet on other forums, but a few of my bro's post/boast over here. So I will post a few of my small grow to get advice and share ideas with folks here as well. This is my clone room and mother plant. I use four 20w florescent bulbs. I turn half off when not cloning. 1st day in main room. Everything is in place for new grow. Turn on the light! Looking for leaks. I use no glue, sealer, or metal parts. 400w Grow tube. It does not draw air from the room. The room is a closed system. The plants have a max height of 5'6". I have not had to raise the light to max height yet. I like to keep the plants at about 4'6". The screen is to keep the plant stable and help train uniform growth. I use two air pumps that feed three buckets. Each bucket has two airstones. TDS and PH sensors screw into the side of bucket. Co2 control with tank. Top half of my controls. Co2 valves and thermostat. One intake for the cooling of the light and the other in case the grow gets above 85* Dampers on the grow intake and exhust to maintain high Co2 levels in the room. A 6" blower on a thermostat to cool the room and a 4" blower that cools the light. The light stays cool with a 4" blower that stays on. The air is piped into the light from the outside. The noise from the air rushing into the closet was so loud, I had to build a muffler on the intake as well. It's kinda hard to get photos of how I did it, so I will have to draw a picture. Have not got around to painting the outside yet. 8 days later, still in veg cycle. 15 days later I am in day 10 of flowering. Its day 16 of flowering and we are at alittle over 5' tall. This is the 5th grow with this set-up. I had four plants last time. I'm only doing three this time. I did my harvest in two cycles, one at 45 days and another at 60 days. Here is a picture of the last two plants I harvested. I put it all in glass jars when done. I hope this grow comes out as well. Peace, R __________________ Lets Build a Clone Machine Step-By-Step Lets Build a Bubble Bucket Step-By-Step My Simple Harvest and Cure Step-By-Step Light Proof Mounting of an Axial/Box/PC Fan My Harvest Pictures Rumple's LED Challenge

#2 (permalink) 07-09-2006, 03:58 PM
cantgetenough Registered User Join Date: Jan 2006 Location: Have a guess Posts: 349	Dame fine set up Rumpleforeskin , gives me some great ideas for my current build.Your 400w cool tube, how close can your plants get before getting damaged? __________________ HIGH TIMES MY FIRST GROW http://forum.grasscity.com/grow-journals/91705-grow-diary-26-april-2006-a.html GROW CLOSET BUILD http://forum.grasscity.com/grow-room-design-setup/100321-grow-closet-design-pics-ideas-needed.html

#3 (permalink) 07-09-2006, 08:59 PM
Rumpleforeskin Legal Medical Grower Join Date: Jul 2006 Location: SoCal Posts: 3,282	It has a dedicated 4" blower that runs the whole time the light is on. It never has a chance to heat up. Touching the tube would be fine, like I am doing in this picture. The glass stays cool. The light radiates warm rays buy not enough to burn or damage plants. I have the light right on the plants today. __________________ Lets Build a Clone Machine Step-By-Step Lets Build a Bubble Bucket Step-By-Step My Simple Harvest and Cure Step-By-Step Light Proof Mounting of an Axial/Box/PC Fan My Harvest Pictures Rumple's LED Challenge

#4 (permalink) 07-09-2006, 10:13 PM
cantgetenough Registered User Join Date: Jan 2006 Location: Have a guess Posts: 349	thanks for the demo.This may be a stupid question but do you think that 2x 4" computer fans will do the job in getting air in and out enough to keep it cool __________________ HIGH TIMES MY FIRST GROW http://forum.grasscity.com/showthread.php?t=91705 GROW CLOSET BUILD http://forum.grasscity.com/showthread.php?t=100321

#5 (permalink) 07-10-2006, 12:27 AM
br3ad_ <-KiNg-> Join Date: Sep 2005 Location: Hamilton, Ontario 9-Oh-5 Posts: 5,357	Holy fuck man. __________________

#7 (permalink) 11-28-2006, 10:09 PM
PurpleStuffed Thoughtless Thoughts..... Join Date: Nov 2006 Posts: 83	Awesome Setup very nice.

#9 (permalink) 12-02-2006, 03:06 AM
CFLdorm Registered User Join Date: Nov 2006 Posts: 194	holy shit. how much did that setup cost you?

#10 (permalink) 12-02-2006, 04:05 AM
naughtyneighbor I said no but I wanted it Join Date: Mar 2006 Posts: 2,814	Damn i can tell this is a pro grow lol __________________ Pro-Pot Article Collection

#11 (permalink) 12-08-2006, 05:34 PM
canoguy Registered User Join Date: Oct 2006 Posts: 58	good stuff best ive seen

#12 (permalink) 12-10-2006, 11:10 PM
Rumpleforeskin Legal Medical Grower Join Date: Jul 2006 Location: SoCal Posts: 3,282	Thanks for the kind words. I rebuilt this closet about 5 times. I love making stuff myself. I shop around for my junk to try and save money when I have to. I'm in my 40's and have a pretty good job, so I can afford to spend on my hobby. That does not mean I toss money out on every cool gadget. I built most my CO2 system (not the meter). I am in the process of moving the CO2 tanks from inside the grow to the attic. I have to run steel pipe the whole way. The guys at the welding shop that I buy CO2 from asked "what are you using CO2 for?". I replied "SCUBA-diving, bucause CO2 is cheeper then compressed air". Thats not the funny part.............The funny part is they all agreed. True story. R __________________ Lets Build a Clone Machine Step-By-Step Lets Build a Bubble Bucket Step-By-Step My Simple Harvest and Cure Step-By-Step Light Proof Mounting of an Axial/Box/PC Fan My Harvest Pictures Rumple's LED Challenge

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

#13 (permalink) 12-11-2006, 03:53 AM
ElDust Banned Join Date: Sep 2006 Posts: 349	Ah, my dream setup!

#14 (permalink) 12-11-2006, 08:55 AM
Rumpleforeskin Legal Medical Grower Join Date: Jul 2006 Location: SoCal Posts: 3,282	After I have this closet working perfect, I plan on following this hobby in the direction of what "Mister Postman" is doing. I like what he has done for indoor growing enthusiast such as myself. If you don't know what I'm talking about, then you have to see what your missing http://forum.grasscity.com/grow-jour...oset-grow.html . Peace, R. __________________ Lets Build a Clone Machine Step-By-Step Lets Build a Bubble Bucket Step-By-Step My Simple Harvest and Cure Step-By-Step Light Proof Mounting of an Axial/Box/PC Fan My Harvest Pictures Rumple's LED Challenge

#15 (permalink) 01-03-2007, 03:36 AM
MrBojangles Registered User Join Date: Oct 2006 Posts: 35	Nice Fucking Setup Man Peace